
Powergrab L+ 220 Bolt on Hooks
Low availability
SKU:
11256201Q
Efficient bucket grab designed for silage handling with large front loaders, telehandlers and wheel loaders.
Bucket grab for Silage handling.
For use with 4 - 5,5 tons lift capacity material handlers.
Compatible with Z-link loaders.
11256201Q
Powergrab L+ is a powerfull bucket grab designed for material handlers with a lift capacity of 3 - 5,5 tons. Powergrab L+ is primarily designed for agriculture silage handling, but is also suitable for various grabbing and scooping work of loose materials. The movement of grab head is done by two powerful cylinders and its design provides several features for increased life length and versatlity such as four anchor points and center take-out to create clearence when using loaders with Z-link kinematics. To increase efficiency the grab head also has extra bars on top to surely hold down the material and to avoid spillage. The bucket gable and grab head side tines are also designed to efficiently prevent spillage through the sides. The bucket body has an integrated spillguard on the top preventing spillage backwards - all in all a high efficient Implement where grabbed material is properly held in place. Grab Bucket is filled by angle the implement down at about 45 degrees into the silage. This gives the maximum fill possible when the grab head is closed. The design of the tines in the grab head and in combination with rotating the implement downwards, creates an even block of silage without creating any air pockets and generating heat in the silage. The cutting edge extrudes minimal at each side and the grab head can open up considerably leaving the tip of the tines behind the cutting edge, these two features minimizes material left close to walls both in front and at the sides. Powergrab L+ is available with Bolt on Hook system M24 that makes it possible to attach it to all most common AG material handlers in this size segment. A optional bolt on cutting edge is also available that will minimize wear on the Implement.
Weight | 957 kg |
---|---|
Width | 220 cm |
Depth | 122 cm |
Height | 124 cm |
SizeModel | 220 |
Hydraulic Pressure, max | 230 |
Working depth | 100 cm |
Working width | 217 cm |
Cutting Edge Dim (WxT) | 200x20mm |
Cutting Edge Hardness | 500 HB |
Volume | 1.75 m³ |
Height, max | 200 cm |
Opening, max | 199 cm |
Tine spacing, grab | 37.25 cm |
Number of Cylinders | 2 |
Number of Tines, grab | 6 |
Start by selecting tool carrier to get the right options:
Bolt on hook for implements with M24 interface.
Powergrab L+; Good fit with AR550-560. Not recommended for AR580 due to possible collisions with Z-linkage.
Powergrab XL+; Recommneded for AR580 but potential collision at lowest position. Not recommended for AR550-560.
Bolt on hook for implements with M24 interface.
Recommended for grabs, gives more dump angle.
Compatible with tool carriers with manual locking pin.
Fits Claas Scorpion, Kramer KT, Liebherr and Weidemann Telehandlers.
Bolt on hook for implements with M24 interface.
Bolted hook for implements with M24 interface.
Recommended for JCB 535-95 telehandler. Double hook lets you choose between increased crowd or dump angle. For both buckets and grabs.
Bolted hook for implements with M24 interface.
Recommended for grabs, gives more dump angle.
Bolt on hook for implements with M24 interface.
Bolt on hook for implements with M24 interface.
Recommended for Bucket grabs for Manitou MLT telehandlers.
Recommended for buckets for Massey Ferguson & Bobcat telehandlers with Manitou tool carrier.
Bolt on hook for implements with M24 interface.
Recommended for bucket grabs for Massey Ferguson & Bobcat telehandlers with Manitou tool carrier.
Bolted hook for implements with M24 interface.
Recommended for grabs, gives more dump angle.
BoH has two adjustable bolts intended to absorb forces and relieve locking pin.
Bolt on hook for implements with M24 interface.
Bolt on hook for implements with M24 interface.
Steel plugs to cover cutting edge holes. For customers loading very loose materials such as grain with + buckets (e.g. VXL+, VL+, GXL+…) and not request to have a bolt on cutting edge, these plugs can be fitted into the holes of the cutting edge to prevent spillage.
Best choice for Volvo wheel loaders.
Hose kit with 2 hoses. 1/2" hoses L 225cm. Coupling towards implement: 1/2" BSPP, Coupling towards loader: 3/4" TEMA Quick Coupling Female.
Hose kit with 2 hoses. 1/2" hoses L 75cm. Coupling towards implement: 1/2" BSPP, Coupling towards loader: 1/2" ISO A Quick Coupling Female.
Universal hose kit with 2 hoses with M22 female thread allows you to assemble the coupling you need, e.g. MX Mach 2.
1/2" hoses L 75cm. Coupling towards implement: 1/2" BSPP, Coupling towards loader: M22x1,5 Female.
Hose kit with 2 hoses. 1/2" hoses L 125cm. Coupling towards implement: 1/2" BSPP, Coupling towards loader: 1/2" ISO A Quick Coupling Female.
Universal hose kit with 2 hoses with M22 female thread allows you to assemble the coupling you need, e.g. MX Mach 2.
1/2" hoses L 125cm. Coupling towards implement: 1/2" BSPP, Coupling towards loader: M22x1,5 Female.
Load hold valve keeps the grab head in position after the 3rd service is deactivated. Required for handlers with open-center 3rd service valves.
Needed when supplied hydraulic pressure exceeds 230 bar.
or |
Note: Select CSV (; separated) file that contains: SKU (sku) and Quantity (qty) to add to cart